I have an ATI TV-Wonder that works under XawTV. Under MPlayer, it shows garbage. This garbage is identical to what I see in XawTV if the NORM setting is not set to NTSC, my local normalization. I grabbed some kernel output from loading the card's drivers. That is below the message. The curious thing, and what I'm certain is the problem, is that while loading, MPlayer says: Tuner isn't capable to set norm! However, it obviously must be capable because XawTV can do it! Is there any solution to this? If I can get the tuner into NTSC everything should be fine. Regards, Chad Kernel output from driver load: --------------------------------------------------------- Feb 15 11:01:07 lola bttv: driver version 0.7.91 loaded Feb 15 11:01:07 lola bttv: using 8 buffers with 2080k (16640k total) for capture Feb 15 11:01:07 lola bttv: Host bridge is VIA Technologies, Inc. VT8605 [ProSavage PM133] Feb 15 11:01:07 lola bttv: Bt8xx card found (0). Feb 15 11:01:07 lola PCI: Found IRQ 14 for device 00:0a.0 Feb 15 11:01:07 lola PCI: Sharing IRQ 14 with 00:0a.1 Feb 15 11:01:07 lola bttv0: Bt878 (rev 17) at 00:0a.0, irq: 14, latency: 32, memory: 0xde000000 Feb 15 11:01:07 lola bttv0: detected: ATI TV Wonder [card=63], PCI subsystem ID is 1002:0001 Feb 15 11:01:07 lola bttv0: using: BT878(ATI TV-Wonder) [card=63,insmod option] Feb 15 11:01:07 lola i2c-algo-bit.o: Adapter: bt848 #0 scl: 1 sda: 1 -- testing... Feb 15 11:01:07 lola i2c-algo-bit.o:1 scl: 1 sda: 0 Feb 15 11:01:07 lola i2c-algo-bit.o:2 scl: 1 sda: 1 Feb 15 11:01:07 lola i2c-algo-bit.o:3 scl: 0 sda: 1 Feb 15 11:01:07 lola i2c-algo-bit.o:4 scl: 1 sda: 1 Feb 15 11:01:07 lola i2c-algo-bit.o: bt848 #0 passed test. Feb 15 11:01:07 lola tuner: probing bt848 #0 i2c adapter [id=0x10005] Feb 15 11:01:07 lola tuner: chip found @ 0xc0 Feb 15 11:01:07 lola bttv0: i2c attach [client=Temic NTSC (4032 FY5),ok] Feb 15 11:01:07 lola i2c-core.o: client [Temic NTSC (4032 FY5)] registered to adapter [bt848 #0](pos. 0). Feb 15 11:01:07 lola i2c-core.o: adapter bt848 #0 registered as adapter 0. Feb 15 11:01:07 lola bttv0: i2c: checking for MSP34xx @ 0x80... found Feb 15 11:01:07 lola i2c-core.o: driver i2c msp3400 driver registered. Feb 15 11:01:07 lola msp34xx: init: chip=MSP3445G-B8, has NICAM support Feb 15 11:01:07 lola msp3410: daemon started Feb 15 11:01:07 lola bttv0: i2c attach [client=MSP3445G-B8,ok] Feb 15 11:01:07 lola i2c-core.o: client [MSP3445G-B8] registered to adapter [bt848 #0](pos. 1).