[MPlayer-users] ffserver and ffmpeg with linksys internet camera

Wed May 30 14:38:35 CEST 2007

I am running ffserver, then running
ffmpeg -i http://192.168.1.115/img/video.asf http://localhost:8090/feed1.ffm
I then run
mplayer http://192.168.1.8:8090/test.asf on my windows machine.

I then get an error from ffmeg that states:
[mpeg1video @ 0x8b03a0]MPEG1/2 does not support 5/1 fps

Below is my ffserver.conf... I first started with the docs/ffserver.conf 
and had the
same above error. I then started to comment out lines seeing if that 
made a difference. It did not.
I am running centos 4 x86_64,  AMD 64  X2 4800+, 1GIG RAM.

I am basically wanting to have my linux server connect to the linksys 
camera (limited connections to the camera)
then use ffserver to just simply relay the video.

What do I do about the MPEG error?

THanks,

Jerry

---------------------

# Port on which the server is listening. You must select a different
# port from your standard HTTP web server if it is running on the same
# computer.
Port 8090

# Address on which the server is bound. Only useful if you have
# several network interfaces.
BindAddress 0.0.0.0

# Number of simultaneous requests that can be handled. Since FFServer
# is very fast, it is more likely that you will want to leave this high
# and use MaxBandwidth, below.
MaxClients 1000

# This the maximum amount of kbit/sec that you are prepared to
# consume when streaming to clients.
MaxBandwidth 1000

# Access log file (uses standard Apache log file format)
# '-' is the standard output.
CustomLog -

# Suppress that if you want to launch ffserver as a daemon.
NoDaemon

##################################################################
# Definition of the live feeds. Each live feed contains one video
# and/or audio sequence coming from an ffmpeg encoder or another
# ffserver. This sequence may be encoded simultaneously with several
# codecs at several resolutions.

<Feed feed1.ffm>

# You must use 'ffmpeg' to send a live feed to ffserver. In this
# example, you can type:
#
# ffmpeg http://localhost:8090/feed1.ffm

# ffserver can also do time shifting. It means that it can stream any
# previously recorded live stream. The request should contain:
# "http://xxxx?date=[YYYY-MM-DDT][[HH:]MM:]SS[.m...]".You must specify
# a path where the feed is stored on disk. You also specify the
# maximum size of the feed, where zero means unlimited. Default:
# File=/tmp/feed_name.ffm FileMaxSize=5M
File /tmp/feed1.ffm
FileMaxSize 200K

# You could specify
# ReadOnlyFile /saved/specialvideo.ffm
# This marks the file as readonly and it will not be deleted or updated.

# Specify launch in order to start ffmpeg automatically.
# First ffmpeg must be defined with an appropriate path if needed,
# after that options can follow, but avoid adding the http:// field
#Launch ffmpeg

# Only allow connections from localhost to the feed.
ACL allow 127.0.0.1

</Feed>

##################################################################
# Now you can define each stream which will be generated from the
# original audio and video stream. Each format has a filename (here
# 'test1.mpg'). FFServer will send this stream when answering a
# request containing this filename.

<Stream test1.mpg>

# coming from live feed 'feed1'
Feed feed1.ffm

# Format of the stream : you can choose among:
# mpeg       : MPEG-1 multiplexed video and audio
# mpegvideo  : only MPEG-1 video
# mp2        : MPEG-2 audio (use AudioCodec to select layer 2 and 3 codec)
# ogg        : Ogg format (Vorbis audio codec)
# rm         : RealNetworks-compatible stream. Multiplexed audio and video.
# ra         : RealNetworks-compatible stream. Audio only.
# mpjpeg     : Multipart JPEG (works with Netscape without any plugin)
# jpeg       : Generate a single JPEG image.
# asf        : ASF compatible streaming (Windows Media Player format).
# swf        : Macromedia Flash compatible stream
# avi        : AVI format (MPEG-4 video, MPEG audio sound)
# master     : special ffmpeg stream used to duplicate a server
Format mpeg

# Bitrate for the audio stream. Codecs usually support only a few
# different bitrates.
#jpgAudioBitRate 32

# Number of audio channels: 1 = mono, 2 = stereo
AudioChannels 1

# Sampling frequency for audio. When using low bitrates, you should
# lower this frequency to 22050 or 11025. The supported frequencies
# depend on the selected audio codec.
#jpgAudioSampleRate 44100

# Bitrate for the video stream
#jpgVideoBitRate 64

# Ratecontrol buffer size
#jpgVideoBufferSize 40

# Number of frames per second
#jpgVideoFrameRate 3

# Size of the video frame: WxH (default: 160x128)
# The following abbreviations are defined: sqcif, qcif, cif, 4cif, qqvga,
# qvga, vga, svga, xga, uxga, qxga, sxga, qsxga, hsxga, wvga, wxga, wsxga,
# wuxga, woxga, wqsxga, wquxga, whsxga, whuxga, cga, ega, hd480, hd720,
# hd1080
#jpgVideoSize 640x480

# Transmit only intra frames (useful for low bitrates, but kills frame rate).
#VideoIntraOnly

# If non-intra only, an intra frame is transmitted every VideoGopSize
# frames. Video synchronization can only begin at an intra frame.
#jpgVideoGopSize 12

# More MPEG-4 parameters
# VideoHighQuality
# Video4MotionVector

# Choose your codecs:
#AudioCodec mp2
#VideoCodec mpeg1video

# Suppress audio
#NoAudio

# Suppress video
#NoVideo

#VideoQMin 3
#VideoQMax 31

# Set this to the number of seconds backwards in time to start. Note that
# most players will buffer 5-10 seconds of video, and also you need to allow
# for a keyframe to appear in the data stream.
#Preroll 15

# ACL:

# You can allow ranges of addresses (or single addresses)
#ACL ALLOW <first address> <last address>

# You can deny ranges of addresses (or single addresses)
#ACL DENY <first address> <last address>

# You can repeat the ACL allow/deny as often as you like. It is on a per
# stream basis. The first match defines the action. If there are no matches,
# then the default is the inverse of the last ACL statement.
#
# Thus 'ACL allow localhost' only allows access from localhost.
# 'ACL deny 1.0.0.0 1.255.255.255' would deny the whole of network 1 and
# allow everybody else.

</Stream>

##################################################################
# Example streams

# Multipart JPEG

#<Stream test.mjpg>
#Feed feed1.ffm
#Format mpjpeg
#VideoFrameRate 2
#VideoIntraOnly
#NoAudio
#Strict -1
#</Stream>

# Single JPEG

#<Stream test.jpg>
#Feed feed1.ffm
#Format jpeg
#VideoFrameRate 2
#VideoIntraOnly
##VideoSize 352x240
#NoAudio
#Strict -1
#</Stream>

# Flash

#<Stream test.swf>
#Feed feed1.ffm
#Format swf
#VideoFrameRate 2
#VideoIntraOnly
#NoAudio
#</Stream>

# ASF compatible

<Stream test.asf>
Feed feed1.ffm
Format asf
VideoSize 640x480
</Stream>

# MP3 audio

#<Stream test.mp3>
#Feed feed1.ffm
#Format mp2
#AudioCodec mp3
#AudioBitRate 64
#AudioChannels 1
#AudioSampleRate 44100
#NoVideo
#</Stream>

# Ogg Vorbis audio

#<Stream test.ogg>
#Feed feed1.ffm
#Title "Stream title"
#AudioBitRate 64
#AudioChannels 2
#AudioSampleRate 44100
#NoVideo
#</Stream>

# Real with audio only at 32 kbits

#<Stream test.ra>
#Feed feed1.ffm
#Format rm
#AudioBitRate 32
#NoVideo
#NoAudio
#</Stream>

# Real with audio and video at 64 kbits

#<Stream test.rm>
#Feed feed1.ffm
#Format rm
#AudioBitRate 32
#VideoBitRate 128
#VideoFrameRate 25
#VideoGopSize 25
#NoAudio
#</Stream>

##################################################################
# A stream coming from a file: you only need to set the input
# filename and optionally a new format. Supported conversions:
#    AVI -> ASF

#<Stream file.rm>
#File "/usr/local/httpd/htdocs/tlive.rm"
#NoAudio
#</Stream>

#<Stream file.asf>
#File "/usr/local/httpd/htdocs/test.asf"
#NoAudio
#Author "Me"
#Copyright "Super MegaCorp"
#Title "Test stream from disk"
#Comment "Test comment"
#</Stream>

##################################################################
# RTSP examples
#
# You can access this stream with the RTSP URL:
#   rtsp://localhost:5454/test1-rtsp.mpg
#
# A non-standard RTSP redirector is also created. Its URL is:
#   http://localhost:8090/test1-rtsp.rtsp

#<Stream test1-rtsp.mpg>
#Format rtp
#File "/usr/local/httpd/htdocs/test1.mpg"
#</Stream>

##################################################################
# SDP/multicast examples
#
# If you want to send your stream in multicast, you must set the
# multicast address with MulticastAddress. The port and the TTL can
# also be set.
#
# An SDP file is automatically generated by ffserver by adding the
# 'sdp' extension to the stream name (here
# http://localhost:8090/test1-sdp.sdp). You should usually give this
# file to your player to play the stream.
#
# The 'NoLoop' option can be used to avoid looping when the stream is
# terminated.

#<Stream test1-sdp.mpg>
#Format rtp
#File "/usr/local/httpd/htdocs/test1.mpg"
#MulticastAddress 224.124.0.1
#MulticastPort 5000
#MulticastTTL 16
#NoLoop
#</Stream>

##################################################################
# Special streams

# Server status

<Stream stat.html>
Format status

# Only allow local people to get the status
ACL allow localhost
ACL allow 192.168.0.0 192.168.255.255

#FaviconURL http://pond1.gladstonefamily.net:8080/favicon.ico
</Stream>

# Redirect index.html to the appropriate site

<Redirect index.html>
URL http://www.ffmpeg.org/
</Redirect>