[Mplayer-dvb] [PATCH] update to dvb-input(2)

[linuxdep]

Hi,

yesit's pssible that mplayer supports any kards and always...
mutation ist not always bad, my english is bad ;-(
what i mean is, that i correct understand. I can now watch TV with mplayer,
without vdr, i only need dvb-s driver...

linuxdep

----- Original Message -----
From: "Beppe" <mplayer at beep.mine.nu>
To: "Mplayer with Siemens-DVB card" <mplayer-dvb at mplayerhq.hu>
Sent: Saturday, January 25, 2003 6:47 PM
Subject: Re: [Mplayer-dvb] [PATCH] update to dvb-input(2)


> Hi,
>
> linuxdep wrote:
> > Hallo,
> >
> > understand i it's right,? This patch allow my watch tv with mplayer rc3
> > without vdr?
> > Then the Mplayer mutate to a tv programm?
>
> Don't you know that mplayer supports bttv cards?
> So, it no some mutation.
> Mplayer now supports bttv and dvb :O)
>
> good work!
>
> regards,
> ::beppe
>
> >
> > linuxdep
> >
> > ----- Original Message -----
> > From: "nico" <nsabbi at libero.it>
> > To: <Mplayer-dvb at mplayerhq.hu>
> > Sent: Saturday, January 25, 2003 3:42 PM
> > Subject: [Mplayer-dvb] [PATCH] update to dvb-input(2)
> >
> >
> >
> >>Hello,
> >>attached is a new patch for Mplayer 0.90rc3 that enables dvb tuning and
> >>channel switching.
> >>
> >>It also includes a couple of last-minute updates respect to the one that
> >>I sent to mplayer-dev-eng.
> >>
> >>It's not ready for the main branch yet, because it still uses an
> >>external ts2ps routine in the streaming layer, and uses some
> >>'Argh!-able' code,
> >>but it's better than the
> >>previous version because:
> >>1) it handles diseqc
> >>2) it tunes much faster
> >>3) it doesn't hang anymore when switching to a channel  with a different
> >>resolution/br
> >>4) it handles other (untested) parameters necessary for DVB-T and -C.
> >>
> >>Yet it still hangs when switching to an encrypted channel.
> >>
> >>Once again all the code is based on dvbstream (thanks to the authors).
> >>
> >>How to use it:
> >>mplayer -dvbin on=1:[PARAMS]
> >>
> >>where the possible params are:
> >>
> >>on=1            required
> >>prog=name (taken from a VDR-compatible channels.conf file that must be
> >>in your .mplayer dir)
> >>freq: frequency, int
> >>vid, aid are pids (int)
> >>srate: symbol-rate, int
> >>pol: char V/H
> >>diseqc: int 1-4
> >>qam: modulation (16, 32, 64, 128, 256, otherwise default)
> >>gi: guard_interval (4, 8, 16, 32, otherwise default)
> >>tm: trasmission_mode (2,8 otherwise default)
> >>bw: bandwidth(6, 7, 8, otherwise default)
> >>cr: coderate (12, 23, 34, 56, 78, -1=auto)
> >>tone: 0/1 maybe totally useless
> >>
> >>e.g.: mplayer -dvbin on=1:prog=Rai1
> >>        mplayer -dvbin
> >>on=1:freq=11766:srate=27500:pol=V:aid=80:vid=160:diseqc=1
> >>
> >>I paid attention to avoid to issue a diseqc command if the next channel
> >>is on
> >>the same satellite as the previous.
> >>
> >>The channels can be switched up and down with 'h' and 'k' keys (as for
> >>the TV).
> >>
> >>
> >>I tested this patch with my Hauppage WinTV Nova-S, so I couldn't test at
> >>all certain parameters specific to DVB-T. If you want, use them at your
> >>own ris but don't consider me responsible if your card fries.
> >>
> >>I hope to receive bug-reports.
> >>
> >>Thanks,
> >>
> >>                Nico
> >>
> >
> >
> >
>
> --------------------------------------------------------------------------
--
> > ----
> >
> >
> >
> >>_______________________________________________
> >>Mplayer-dvb mailing list
> >>Mplayer-dvb at mplayerhq.hu
> >>http://mplayerhq.hu/mailman/listinfo/mplayer-dvb
> >>
> >
> >
> >
> > _______________________________________________
> > Mplayer-dvb mailing list
> > Mplayer-dvb at mplayerhq.hu
> > http://mplayerhq.hu/mailman/listinfo/mplayer-dvb
> >
> >
>
>
> _______________________________________________
> Mplayer-dvb mailing list
> Mplayer-dvb at mplayerhq.hu
> http://mplayerhq.hu/mailman/listinfo/mplayer-dvb
>
>