[FFmpeg-user] ffmpeg cannot capture audio from capture card

[Md Ismail, Zakiah]

I did not get a valid wav file. The duration here is 0.
$ ffprobe test.wav
Input #0, wav, from 'test.wav':
  Metadata:
    encoder         : Lavf58.12.100
  Duration: 00:00:00.00, bitrate: 1688 kb/s
    Stream #0:0: Audio: pcm_s16le ([1][0][0][0] / 0x0001), 48000 Hz, 2 channels, s16, 1536 kb/s

Using arecord, I was able to get a valid wav file. For example here, I managed to get a 10 seconds wav file - but the recording is a complete silent. Please refer to my logs below.

On target:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC283 Analog [ALC283 Analog]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 7: HDMI 1 [HDMI 1]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 8: HDMI 2 [HDMI 2]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 9: HDMI 3 [HDMI 3]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 10: HDMI 4 [HDMI 4]
  Subdevices: 1/1
  Subdevice #0: subdevice #0

$ sudo aplay -Dplughw:CARD=PCH,DEV=3 beep.wav
Playing WAVE 'beep.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Mono

On host - which was where I ran the ffmpeg command last time:
$ arecord -v hw:CARD=nuc-03i,DEV=0 -d 10 arecord.wav
Recording WAVE 'hw:CARD=nuc-03i,DEV=0' : Unsigned 8 bit, Rate 8000 Hz, Mono
ALSA <-> PulseAudio PCM I/O Plugin
Its setup is:
  stream       : CAPTURE
  access       : RW_INTERLEAVED
  format       : U8
  subformat    : STD
  channels     : 1
  rate         : 8000
  exact rate   : 8000 (8000/1)
  msbits       : 8
  buffer_size  : 4000
  period_size  : 1000
  period_time  : 125000
  tstamp_mode  : NONE
  tstamp_type  : GETTIMEOFDAY
  period_step  : 1
  avail_min    : 1000
  period_event : 0
  start_threshold  : 1
  stop_threshold   : 4000
  silence_threshold: 0
  silence_size : 0
  boundary     : 9007199254740992000
Recording WAVE 'arecord.wav' : Unsigned 8 bit, Rate 8000 Hz, Mono
ALSA <-> PulseAudio PCM I/O Plugin
Its setup is:
  stream       : CAPTURE
  access       : RW_INTERLEAVED
  format       : U8
  subformat    : STD
  channels     : 1
  rate         : 8000
  exact rate   : 8000 (8000/1)
  msbits       : 8
  buffer_size  : 4000
  period_size  : 1000
  period_time  : 125000
  tstamp_mode  : NONE
  tstamp_type  : GETTIMEOFDAY
  period_step  : 1
  avail_min    : 1000
  period_event : 0
  start_threshold  : 1
  stop_threshold   : 4000
  silence_threshold: 0
  silence_size : 0
  boundary     : 9007199254740992000

Is there anything that I'm missing here? Am I supposed do some configurations?