[FFmpeg-cvslog] doc/encoders: add libopus encoder doc

[Timothy Gu]

ffmpeg | branch: master | Timothy Gu <timothygu99 at gmail.com> | Fri Jul  5 20:37:18 2013 -0700| [561e05136f1cbe28a79af1940aa137f70281eef4] | committer: Stefano Sabatini

doc/encoders: add libopus encoder doc

Signed-off-by: Stefano Sabatini <stefasab at gmail.com>

> http://git.videolan.org/gitweb.cgi/ffmpeg.git/?a=commit;h=561e05136f1cbe28a79af1940aa137f70281eef4
---

 doc/encoders.texi |   73 +++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 73 insertions(+)

diff --git a/doc/encoders.texi b/doc/encoders.texi
index afe4952..fb47586 100644
--- a/doc/encoders.texi
+++ b/doc/encoders.texi
@@ -600,6 +600,79 @@ default value is 0 (disabled).
 
 @end table
 
+ at section libopus
+
+libopus Opus Interactive Audio Codec encoder wrapper.
+
+Requires the presence of the libopus headers and library during
+configuration. You need to explicitly configure the build with
+ at code{--enable-libopus}.
+
+ at subsection Option Mapping
+
+Most libopus options are modeled after the @command{opusenc} utility from
+opus-tools. The following is an option mapping chart describing options
+supported by the libopus wrapper, and their @command{opusenc}-equivalent
+in parentheses.
+
+ at table @option
+
+ at item b (@emph{bitrate})
+Set the bit rate in bits/s.  FFmpeg's @option{b} option is
+expressed in bits/s, while @command{opusenc}'s @option{bitrate} in
+kilobits/s.
+
+ at item vbr (@emph{vbr}, @emph{hard-cbr}, and @emph{cvbr})
+Set VBR mode. The FFmpeg @option{vbr} option has the following
+valid arguments, with the their @command{opusenc} equivalent options
+in parentheses:
+
+ at table @samp
+ at item off (@emph{hard-cbr})
+Use constant bit rate encoding.
+
+ at item on (@emph{vbr})
+Use variable bit rate encoding (the default).
+
+ at item constrained (@emph{cvbr})
+Use constrained variable bit rate encoding.
+ at end table
+
+ at item compression_level (@emph{comp})
+Set encoding algorithm complexity. Valid options are integers in
+the 0-10 range. 0 gives the fastest encodes but lower quality, while 10
+gives the highest quality but slowest encoding. The default is 10.
+
+ at item frame_duration (@emph{framesize})
+Set maximum frame size, or duration of a frame in milliseconds. The
+argument must be exactly the following: 2.5, 5, 10, 20, 40, 60. Smaller
+frame sizes achieve lower latency but less quality at a given bitrate.
+Sizes greater than 20ms are only interesting at fairly low bitrates.
+The default of FFmpeg is 10ms, but is 20ms in @command{opusenc}.
+
+ at item packet_loss (@emph{expect-loss})
+Set expected packet loss percentage. The default is 0.
+
+ at item application (N.A.)
+Set intended application type. Valid options are listed below:
+
+ at table @samp
+ at item voip
+Favor improved speech intelligibility.
+ at item audio
+Favor faithfulness to the input (the default).
+ at item lowdelay
+Restrict to only the lowest delay modes.
+ at end table
+
+ at item cutoff (N.A.)
+Set cutoff bandwidth in Hz. The argument must be exactly one of the
+following: 4000, 6000, 8000, 12000, or 20000, corresponding to
+narrowband, mediumband, wideband, super wideband, and fullband
+respectively. The default is 0 (cutoff disabled).
+
+ at end table
+
 @section libwavpack
 
 A wrapper providing WavPack encoding through libwavpack.